Wednesday, June 28, 2017

Cleaning up bottom


I finally bit the bullet and decided to take the skirt off and fix up the bottom of the hovercraft.

I'll also use this time to change the skirts from the plastic drop cloth to the proper rubber surfaces. I still have some experimentation but I found that the plastic had failed in several places already.


Tears in the front port interior corner. These were clearly from rubbing back on the skid bars.

Tears in the front starboard interior corner.

A little bit of the wear and tear can be seen on the skirts here. With roughing going on down the sides.
Here's a full timelapse of removing the skirt.


I also made some interesting discoveries inside the bag. With non-trivial amounts of dirt of non-trivial size. I guess the smaller stuff blew out at some point.

There was also a surprising amount of dirt inside the skirt

After removing the skirt my next step is to clean up and seal the bottom of the hull. The top of the hull has been fiberglass reinfored at the joints but not the bottom yet. This is both putting the full load on the foam, as well as providing surfaces for water intrusion.

So with a bunch of help from Jenny I've tipped the hovercraft up on it's side. Here's a video it was a good anount of effort. 


Here's the final result

Here it is resting on the fan housing, it makes a nice roll bar...

And the bottom you can see the blemishes clearly in the streaking sunlight.
 There's a bunch of work to do down here. For example the corners especially the front and rear need some reinforcing.


And one of the skid boards, is only attached in the front half.
I can fit my whole finger behind the skid board.

However the skid boards appear to be doing their job well. There was no noticable damage to the skirt attachments and there was clearly some wear and tear on the skid boards themselves.

An example of the wear on the skid boards up close.
Here's some closeups of the joints that need reinforcement. Clearly glue on foam w/o vacuum application doesn't really work too well. I'll make up for it with some good fiber/epoxy corners.

The bottom edge of the bow.


Bubbling along the bottom of the boat.

The dolly mechanism does appear to have left some wear and tear on the transom.

Damage to the bottom edge of the transom?

A second view of the transom damage

Tuesday, January 24, 2017

Upgraded lift throttle control

I received the sampling of throttle control levers and installed the best looking one last night.

Here's a view of the throttle control installed. It's nice and solid, as well as stiff and seems like it will hold despite the vibrations.

Front view

Side view

Sunday, November 6, 2016

Hover test again

I put everything back together with help from Michael today. I think we're almost ready for another field test!


We added one enhancement for the lift fan. A little bit of rubber padding between the engine mount and the safety grill. I hope that this will avoid any rattling between the two. And it should also take out some of the vibrations.

Rubber padding installed

Close up of the rubber padding during the installation process

Our simple design is reusing some used RC car tires. They're cut and splayed open. And then zip tied to the engine mount.

One thing we noticed and were surprised about was the amount of rust that's accumulated on the engine mount. There's nothing structural, but it was more than we were expecting since the craft has always been in the garage.

One other thing that we had to do was to bang out the small indent where the lift fan cowling was slightly dented from its past life with wheels mounted there.

We also tested again with the sound meter. Even with the padding the lift fan is still at similar levels. Mid to high 90s db at idle and almost 105db throttled up.

Here's me trying out the new mount with the fan and exploring the envelope of CG which is now much larger.


We tested out the thrust fan too. Again the engine noise is basically all the noise and it ranges from the mid 90s up to just over 110db at full throttle. It also appears to be the majority of the noise coming from the engine. Of course the

Sunday, October 2, 2016

Testing the twist throttle

With a trip to the store to get a handle bar and reusing some of the pieces from the oarlocks I've successfully mounted the thrust engine twist throttle at the front of the cockpit.

The twist throttle mounted

It took a while to find a part at the bikeshop with a long enough straight section.  But cruisers have some long segments in their handlebars ...

The handlebars I repurposed. (note I used the longest straight section below the first bend.)
And here's a quick test: 


I also thought about mounting it on the tiller too. I didn't have enough slack in the control cable at the moment. But I think that the current mounting will provide a nice solid handle for the pilot to lean against.

The engine needs to warm up a bit before it can throttle up effectively. You can see some lag, it was way better this time than the first time I tested it completely cold. Opening up the throttle completely flooded the engine.

Tuesday, August 30, 2016

New Throttle Linkage

With the new propeller I also purchased a new throttle linkage. So I needed to find the best way to hook it up. So to get the best look at the possible throttle mechanisms I ended up tearing down the engine. Now you can see the governor and throttle linkages clearly. 
The twist throttle linkage

Top view of the engine with gas tank and air filter removed

The air filters for reference

The engine with the gas tank and air filter removed, and screws on the ground
The end results of my research was to identify that the best place to attach the throttle is actually on the exterior handle. 

My final solution

The bare end

A little bit of electrical tape for grip

Three zip ties to hold axially

Another view of the zip ties, also showing the zip tie with the screw attachment point.

After using pliers to tighten the zip ties

The zip ties trimmed

The zip tie mount installed on the front of the engine

Demonstrating the mechanism
With the friction released the external handle does not hold position. And removing my other throttle mechanism we're now able to control the throttle with a twist of the wrist. 

It's a little bit more sensitive than I'd like, but being able to change throttle quickly will be nice. And I suspect that most control will be bang bang style anyway.  Right now there's not much spring return, but I believe that once the governor spins up the return spring will be tighter and pull it back. Since at stop the governor is leaving the throttle wide open the throttle linkage only tensions at the very end. 

Next up I need to get a handle bar to mount the throttle onto. I'm not sure if it should be on the tiller stick or not. A single joystick control would be nice, but possibly confusing/ergonomically challenging if it requires continuous torque. 

Monday, August 15, 2016

New lift fan!

Today was exciting. I swapped out the lift fan from the Universal Hovercraft kit with a Hascon Wing Fan cut to size 24.5" that I ordered from Slipstream Hover. The size was picked to give 1/4" of clearance on on the 25" interior space I measured and talked with the representative about optimal size to select.

Unpacking the new lift fan
The new fan is a 5 bladed fan. With a cast hub with mounting points for each blade, and a machined collet flange. Each blade is molded plastic cut to length.

I also have a new twist throttle control from them to try out.

The two propellers. Old foreground new background.

When I removed the old fan, it just slid off once I released the shaft end bolt. Clearly the collet was not clamping correctly. 

The new lift fan fit check on the engine shaft


Installing the fan was easy. The collet was nicely layed out that I could easily put the bolts in from the bottom. So I could use a ratcheting socket and tighten it easily and evenly. The shaft is a little worn these days and it tightened further than optimal, but the collet has a full cut instead of just the lower part of the flange which gives it more travel. And after testing the collet appears to be holding successfully. I put the end nut onto the shaft as well which will keep the propeller from sliding off the end of the shaft, but it does not have a plate that prevents the fan from riding up the shaft.


The hub is much more compact and the overall blade is a little bit lighter. But the most important thing is that the blade is noteably more balanced. Looking down when spinning the old fan by hand, the plywood circle could be seen oscillating with at least a 1/4" asymmetry. Which meant that it vibrated the whole system quite a bit.

Here's my first test of the new fan. I spun it up to idle speeds briefly and then inspected it before trying to throttle it up.


A few interesting notes are that with the new fan, it actually was effectively hovering even at idle.

Here's me trying out hovering and moving my weight around on top of the hovercraft with the new fan throttled up.


For reference I filmed a similar segment earlier with the old fan. You can see more vibrations, as well as notice that the vehicle does not lift off even at idle. I was previously worried about the vibrations and was considering more reinforcements for the lift engine mount but I don't think that's necessary anymore.





Noise level: 

I thought that the new fan might be quieter, but apparently not. I think that most of the noise is actually from the engine. I tested both the new and old fan, and idle and full throttle. And I found that it was about the same.
95 db at idle lift only UH fan

105 db at full hover throttle, lift only UH fan.
Here's my testing again with the Hascon fan. My phone was giving me trouble turning on the camera. But the readings were not significantly different than the priors so I didn't bother figuring out why the camera wasn't starting properly. You can see that these measurements were taken between 1 and 2 meters away from the noise.


So although I probably don't need to reinforce the engine mount. A housing to contain the engine noise and protect the fan, as well as provide ram air pressure.


One other note is that the new hub is notably smaller which means that the engine fan is now actually about 2" higher. I was previously considering making the baffle take up more of the lift fan area, however despite the larger gap between the diverter and the fan blades, we're still getting much better performance. Until it's the limiting factor I'll probably drop the priority of refactoring that for now.

One new piece of technology I've deployed now is some tamper marker paint to see if things are vibrating loose.

Tamper paint as first applied

Tamper paint after being run before fully dried
 Above you can see that I didn't quite wait long enough for it to dry. But it's showing that the nuts are not moving.
Additional dot on the shaft to detect upward movement.

As mentioned above the end shaft bolt only keeps the hub from coming off the end of the shaft, so I added this dot of marker paint to show if the hub rides up the shaft at any point. 

Saturday, August 13, 2016

Dirty Hovercraft after test + lift fan optimization

The hovercraft is surprisingly dirty after just a few minutes flying around a "clear" parking lot. 

Dirt collected under the thrust engine

More collected on the side

Another view of the dirt at the rear 


There's even dirt in the center of the fan.  Clearly there's a lack of airflow there...

After cleaning off as much dirt as possible I set to work to improve the hover performance. 

I took two approaches. First I started by clearing out more of the grill wires. It made a large difference for the thrust fan. And since the lift fan is actually well protected, I cleared out 3 of 4 on the bottom, and 2 of 3 on the top except for the outer ring where I did 3 in a row where I expect the highest speed. 

In addition there was a gap between my metal diverter plate and the board that is attached to the skirt attachment leaving about a 3/4" gap across the whole width. And with the wires removed I could now relatively stretch some Duct tape across the gap. I think this might be my first correct use of Duct tape ever!!

Sealing the diverter with duct tape front view

Duct tape rear view

And reassembled
The propeller is much mor eexposed. i plan to build up a higher housing around the lift engine to keep me and other things farther away from the lift engine to avoid any problems with foreign object entries. I'm even thinking of a shroud/hood that will scoop forward air and also dampen the noise hopefully. 

Sunday, July 3, 2016

Successful dry land tests!!

It's been a great day! With help from Adrian and Kelly I have successfully tested the hovercraft in the Redwood City shores boat ramp parking lot!

It's been almost exactly 4.5 years in progress. I was able to successfully control the hovercraft and do laps in the parking lot.

We started with another towed hover test.

We discovered that there's a bunch of dust/and dirt. And unfortunately for my helpers it flys outward quite effectively when over a puddle.

Muddy spray from crossing the puddles

A little bit of mud on the skirt. 

For further testing we decided to stay away from the puddles if possible. And we moved onto testing with the thrust fan and trailing ropes for safety.




Following that I demonstrated being able to travel straight and turn around.
It was a little exciting as the return was downhill.



And here's the view from Adrian's camera.




I started getting pretty confident at stopping and turning around.




Here's Adrian's view.

Not all turns happened as desired...




A gentle brush with the curb.

Slight contact with the curb

And here's the flight afterwards.



And Adrian's chase footage.


Improved flow through the thrust fan

As I identified in the last post there's quite a bit of pressure buildup in the thrust fan. So I've been reducing the drag induced by the protective grill.

The 1cm width is narrower than necessary. So with help from Wim, I've removed every other wire from the front. And 2/3 from the rear of the thrust fan housing.

With these gaps I still cannot reach the propeller even if I try with my hands since it has 3+" of clearance at the front and 6+" inches of clearance at the back.

View from the front of the reduced lift fan grills

Back left view

Back right view

In this process we removed a lot of clippings. The ones I collected weighed 2.4 lbs. Not bad for decreasing the weight at the back.
Most of the clippings removed

Clippings bundled in cling wrap to be weighed. (2.4 lbs)
With so very unscientific testing of standing downwind of the fan, it felt noteably stronger. And throttling up and down did not result in the front grill flexing like it used to do. 

We held back on the lift fan since it's both closer to the pilot as well as lower volume due to having back pressure. With the improved fan mounting the craft is floating much higher, but the CG is still notably aft. To take a passenger I'll probably need to add weight at the front with the current configuration.