It's far from optimal. In particular if I need to do maintenance it will be a big pain as getting inside the housing requires a full disassembly. However it's there and I feel pretty safe with it in place.
I'd also like to decrease the occlusion of the intake. We'll leave that to a 2nd generation however.
One of my worries is about the collet. I hope that it will release when the time comes. The supplied release bolts are black annodized 1/4-20 about 1" long. I removed them as they were just going to be a risk of rattling free.
Fan mount prior to tightening.
The bottom side of the fan with washers added for good measure.
5/16"x3" bolt without washer
Bolting the engine down went fine except that the 5/16ths washer couldn't fit onto the longer engine mount on the backside so I skipped that. But I did find nyloc nuts for better security.
The other two engine bolts before tightening
The engine in position waiting to be bolted down
Thanks to help from Jenny, getting the engine into place was not too hard. I blocked it up briefly while aligning the protection fan, then clamped it down before drilling the clearance holes manually.
I was able to confirm clearance by spinning the fan using the pull start of the engine.
Before powering up, I need to remember to reinforce the cockpit frame with plywood to avoid parallelagramming. A few pieces of left over plywood will take care of that nicely.
Thanks to my helper Jenny today! We successfully inflated the test skirts using
We had to tape together 2 corners. Batten down the perimeter and then make a few tweaks to the starboard hull. (Note it's upside down and pointing into the garage so the starboard side is away from the camera.)
Inflated skirts
Here's the timelapse:
The skirts inflated and could take some weight resting on them with just the shop vac!
Lessons Learned
There were quite a few lessons learned today.
The port side skirt ended up 2" too short, so the front had to wrap around.
Missed front port corner.
The front batten port most screw got started cross threaded, and I tried to force it. Unfortunately the weakest point in the system is the wood the tee-nut is threaded into and I ended up with the tee-nut spinning behind the batten. It took some forceful work with vicegrips to get the screw out. And now the threads in the tee-nut are shot, so I think I'll be grinding that section of the batten out and gluing in a replacement segment with a new tee-nut, since the corner is the most critical portion of the batten.
Cross-threaded
Adjusting the starboard side required a little scrunching:
Scrunched skirt under batten from shifting starboard skirt by 2 inches
Also the rear starboard corner does not quite line up correctly. When transferring the template we need to make sure to take this into account.
Corner length miss alignment. The port side was folder over to match.
Next steps:
Landing pads, to protect the skirt when landing.
Lift engine mount. I think I'll test it out of wood for quick fabrication and testing. Then move onto waterjet cut alumninum. I think the wood will be strong enough for initial testing.
A big thanks to my parents who were in town and gave me a hand this weekend.
We made a bunch of progress on the skirts this weekend. Here's the timelapse:
A few details from the process. We are prototyping the skirts using drop cloth plastic picked up at the hardware store since it's cheap and readily available.
Thinking about how to secure the corners we ran into some zippers for tarps which we thought might be useful.
They did end up being useful, however we didn't use the zipper functionality. They turned into good adhesive tape. In the future I think I will do some research to find some good tape to use for joining the skirt elements. Certainly this tape is as strong as the skirt material. And it has a special zipper like anti abrasive rub surface ;-)
We experimentally determined the curves necessary for the joints using masking tape, the plastic and a shop-vac set to blow.
Prototyping with masking tape
The shape of this curve is quite complicated, and we learned the important part is that they line up, as well as the two pieces have the same linear length along the joint.
Two corners secured using zipper reinforced tape.
I also had not worked on the intake for the skirt at the front. So we added a crossmember under the lift fan to be able to catch the air and route it into the skirt.
Adding scoop area for filling the skirt from the lift fan.
We're not sure about the ratio of lift to skirt, but expect that we can adjust it with a baffle if we need more.
With the glue drying we had to stop work on the front skirt section. But once that dries the front skirt segment should be ready to go too.
Once I've verified the plastic skirt works as I like. i plan to cut it apart and measure it to make my templates for the rubberized vinyl version.
Thanks to Michael and David I have a vinyl cutout of the engine mount as measured. It appears that the through holes are too large and the one of the left is off by about 1 hole width. I'll update this again and either try to interate on the vinyl or else just print on some paper and cut it out.
I've been working on the lift engine mount a bit. I'm still amazed that there does not appear to be a library of these engine bolt hole patterns I can find. Or even specs.
Bottom view lift engine
Working with our measurements I've put together this design.
The layout sketch with dimentions.
There was one redundant constraint and it ended within 1 mm so I think we're close.
A solid rendering
Michael's going to use his vinyl cutter so we can test the layout and if it works we'll work toward water jetting some aluminium.
With the help of Michael I've secured the superstructure to the top deck.
We used drywall anchors to secure the superstructure down, as well as epoxy under the whole perimeter of the structure where contacting the hull.
Below is the timelapse as well as some closeups.
Inserting the drywall anchor into the hull
The drywall anchor inserted into the hull.
At the end we spent some time to measure the engine mount for the lift engine.
Here are our notes:
Engine Mount holes for Briggs and Stratton 8.5 Hp vertical shaft motor.
Our thought was to laser cut an aluminum plate with the necessary hole pattern. We'll also try a vinyl cutout to verify our measurements before getting the metal fabricated.
I did verify that we have almost an inch of play horizontally which should give us plenty of tolerance.
An inch of clearance on one side with the other blade touching the cowling.
Again thanks to Christian for helping out. We've made great progress and the extra hands were very helpful. This time we assembled the stock cut into the first semblance of the superstructure of the craft.
The stock is an unlikely 1.5x1.5" redwood. (Home Depot's selection was less than ideal, but the redwood should work well, and looks quite nice.)
The planning sketches I drew up
To get started I put together a sketch. Here's the version we started with inside. After going out the expected 12" height of the fan was measured to be 10" and the outside radius was 26" so the cross members were extended by 2" and the verticals shortened by 2".
Here's the timelapse of our work.
And the result:
The superstructure placed on the hull. It's not exactly in place as the hull's upside down at the moment, the skirt strips are on the bottom.
There was one complication that the engine mount for the vertical shaft has 3 bolt holes on an recessed circular pattern. The pair of boards going across will not work. We will need to find a more complex solution.
With more help from Christian I've been making great progress. We successfully create all the remaining skirt strips matching pieces.
We made much faster progress by using a small template piece, pictured below. This allowed us to not worry about the lateral alignment and simply make sure it lined up along the length of the strip. All the matching strips are paired to match a particular strip on the hovercraft to match their specific idosyncracities. (aks hand drilling inaccuracies.)
An example of the template for marking the mating strips.
Here's the time-lapse of this stage.
You'll see at the end we also started cutting the stock for the superstructure.
Christian and I made the first two matching strips for the skirt attachments.
This involved cutting them to length, followed by carefully marking out and drilling the clearance holes. We first drilled with 3/16th, but due to imprecisions using hand tools we found 1/4" holes were much more likely to line up.
Here's the time-lapse of our work.
Then end result looks pretty good. I'll need to get some more approximately 5/8" screws.
The 5/8" screws next to the attached skirt.
The corner with both matching skirt strips in place.